• Bowl.
• O-Ring.
• Flange.
• Wax Seal.
• Handle.
• Float.
• Chain.
• Flapper.

Whats in the back of a toilet?

Tank: The back part of the toilet that holds the water used for flushing. It also houses the working toilet parts. Stop Valve: This controls the water supply to the toilet. It's usually located on the wall behind the toilet.

What is the top part of a toilet called?

Tank - The tank is the top portion which holds either the freestanding water to be flushed (gravity-fed) or the pressure-assist cylinder (pressure-assist).

What is cistern in toilet?

A cistern; is a receptacle built to store water. ... In a toilet, the upper part is the cistern which is a small tank that is used to store water for flushing. In toilets, cisterns also hold the right amount of water to enable flushing of the toilet bowl.

What is the valve in the toilet called?

The fill valve (sometimes referred to as a ballcock) brings water into the tank after the toilet is flushed and stays on until the tank refills. Any time water exits the tank (such as when a flapper is leaking), the fill valve will turn on in order to maintain the water level.

What is the valve behind the toilet called?

Stop Valve: This is also called the toilet supply valve because it controls the fresh water supply going into the tank. It is usually located behind the toilet near the floor, and turning it off is another way to stop an overflowing toilet because the tank cannot fill once it is turned off.

What's the pipe behind the toilet called?

If the toilet fill valve doesn't completely shut off at the end of a flush cycle, the overflow pipe is designed to transfer the water from the toilet tank to the toilet bowl and out the drain line. The height of the overflow pipe can be adjusted to prevent water from leaving the tank.

What is wall faced toilet?

A wall faced toilet is mounted directly onto the floor, just like a back to wall toilet, but instead has an in-wall cistern. Unlike a wall hung toilet, there is no gap between the floor and the bottom of the pan. All plumbing and waste pipes flow straight into the wall or floor, making everything hidden from view.

What is a rimless toilet?

A rimless toilet is a toilet without a rim where the water would normally flow from in a traditional toilet. Instead of water flushing down, a rimless toilet has a flushing system that shoots water towards the edge and around the toilet bowl leaving no spots missed.

What is a flush valve?

A flush valve is a part inside the tank of a toilet that moves the water into the bowl. Toilet flush valves come in different sizes ranging from 2 to 4 inches, depending on the toilet design. If you are thinking of buying a new toilet, pay attention to the type of flush valve it has.

What is the small hole in the bottom of the toilet?

This hole is known as the siphon jet. It releases most of the water directly into the siphon tube. Because all of the water in the bowl enters the tank in about three seconds, it is enough to fill and activate the siphon effect, and all of the water and waste in the bowl is sucked out.

Where is the toilet flapper?

The toilet flapper is the component inside your toilet tank that lets water flow out of the tank and into the bowl when you flush. This round, rubber disc is attached to the bottom of the overflow tube, usually by mounting arms that hook onto ears on either side of the overflow tube.

What is a flapper seat on a toilet?

The flapper (aka “flush valve seal”) is the plug that falls against the drain hole (flush valve drain seat) on the bottom of the tank and holds water in until the next time you flush. When flappers or flush valve seats wear out, water trickles out, causing the water valve to open to refill the tank.

What is the difference between a snake and an auger?

Drain snakes work for smaller drains like your kitchen or bathroom sink. Drain augers tackle larger pipes like your toilet or shower drain. The snake covers lines from 1-1/4″ – 2″ range, and you'll use an auger for lines in the 1-1/2″ – 3″ range. ... When they do, it's often from roots growing into the pipes.

What is the difference between a toilet snake and a drain snake?

Snakes are the smaller counterpart to toilet augers. They're normally not the idea choice for a toilet clog but will work in a pinch if that's all you've got. However, snakes are ideal for smaller drains such as sinks and bathtubs. The biggest difference between drain snakes and augers is how they remove the clogs.

How do you unclog a toilet that won't plunge?

We recommend you add a cup of baking soda to your blocked toilet and wait for some minutes. Next, pour two cups of vinegar slowly into the toilet. Vinegar and baking soda will typically react to form bubbles, so ensure you pour carefully and slowly to prevent the toilet water from overflowing or splashing.

What does BTW toilet mean?

One of the most recent popular trends in toilet design is 'Back to Wall' (BTW, for short) and 'Wall Hung' toilets. ... When sitting on the toilet, your back is to the wall, not to a cistern as with standard toilets.

How much should I pay for a good toilet?

Average Prices of Toilets

The average new toilet unit costs around $500. The price can range from as low as $90 to as high as $1,500 for a standard residential toilet. Features that can increase cost include the height, shape and smart capabilities of the unit.

What is the difference between a close coupled toilet and a back to wall toilet?

Close coupled – where the cistern sits directly on the back of the toilet pan. Back to wall – where the toilet pan fits against the wall or a piece of furniture and a concealed cistern provides the water for flushing.

How do you remove a toilet flange?

Remove the toilet flange by unscrewing it from the floor. If the screws are in good condition, save them. You may need to pry out pieces of the old flange with a chisel and hammer. If the flange is really stubborn, it can help to cut it into pieces with a Dremel tool.