1. Turn off power to the unit.
2. Press and hold the CLEAR button. ...
3. While holding the CLEAR button, restore power to the unit. ...
4. Release the CLEAR button and reprogram the transmitter according to the directions found inside the enclosure.

What is Rotary limit switch?

Rotary gear limit switches are used to control the movement of industrial machinery when it's necessary to measure movement based on the rotation angle and/or the number of shaft revolutions, providing upper, lower and/or intermediate limits for moving machinery and mechanisms.

Why is my boat lift not working?

Several factors can contribute to boat lift motor problems, including faulty wiring in the motor, burnt fuses, an incorrect amount of voltage to the motor, and a defective up-button, among others. A marine technician can easily repair motor problems, but a completely damaged motor will require replacing.

Why does my boat lift go up but not down?

If your lift will not lower, with or without the boat, then it is most likely an airflow issue. Double check your valve handle lever(s) to confirm that they are fully in the lift/launch position. Pick up the air hose to make sure that it is not kinked or resting too low below the water's surface.

Is it OK to leave boat lift in water?

Keep Your Dock Lift Out of the Water

Winterizing your boat lift is as easy as taking it out of the water. Leaving your boat lift in the water could result in damage from freezing conditions, especially if you live in an area where ice movement is common.

Should I grease my boat lift cables?

For cable lifts, use a marine-grade grease to lubricate bearings and pulleys. This task should be done every six months or so. ... Cables should be sprayed lubricated every so often. If frayed or broken cables are detected, a boat lift repair technician should be contacted immediately.

How do you program a shore remote control?

Press and hold up and down buttons on the new remote control until the mode one light blinks. Press and hold the programming button located on the lift controller until it beeps once. Electric controllers are located inside the winch case.

How does a rotary limit switch work?

A rotary limit switch works on the principle of a worm drive . ... The gears are attached to a cam mechanism which rotate along with the central gear, a rotary limit switch has a minimum of two cams , one for setting the upper limit of the hoist machinery and one for setting the lower limit of the hoist machinery .

How many types of limit switches are there?

– There are 4 general types of limit switches: whisker, roller, lever, and plunger. – Limit switches are electromechanical devices operated by a physical force applied to it by an object.

Why does my boat lift squeal?

Inexperienced service technicians often will grease up the boat lift. ... That allows the worm gearing to turn through a grease reservoir, which provides continuous lubrication. Insufficient lubrication, however, is only one part of the problem that's causing the terrible noise.

How do I stop my boat lift from squeaking?

Pulleys: The sheaves (pulleys) of a boat lift should be greased every 4-6 months depending on use. If you hear squeaking that's a sign that it's time to grease the sheaves. This prevents the friction from the sheaves and sheave mounts from building up and causing the pulley to seize.

What is marine grade grease?

WD-40 Specialist_® Marine-Grade Grease is a lithium-based grease that provides superior lubrication and corrosion protection in wet and moist environments. ... It resists water wash-out and allows the grease to stay in place in the presence of water while providing rust and corrosion protection.

Can you put a pontoon boat on a boat lift?

Doing It Yourself

If you're fairly handy, it's possible to do a pontoon boat lift conversion at home by building the required parts. If your existing boat lift is already set up with bunks, you can add another set so that each of your boat's pontoons is supported by a pair of bunks.

How do you install a limit switch on a boat lift?

To adjust the lower limit use screw 2o -1(red wire on micro switch). 10: Your lift should be at the max height if you followed the directions above. Loosen retainer screw 1o(½ TO 3/4 TURN) inside the case as shown in the picture below. 11: Adjust the upper limit using screw 2o-2(blue wire).

What do you do with a boat in the winter?